NC Wood Lacquer – Colors

“Lacquer is a form of finish which is harder than Wood polish, and is used to give a clear or coloured shiny, glossy finish for furniture. Due to its high film clarity, NC lacquer combines well with the natural grain of the wood.
Nitrocellulose wood coatings are ideal for transparent topcoats and excellent pore-drawing, give the wood a special warmth and make it incomparably touch-friendly. Suitable for antique, artistic, or country furniture. ”

AREA OF USAGE

Reproduction of classic furniture styles, refurbishing older furniture, vintage musical instruments and interior general millwork. NC lacquers are not recommended for use in kitchens or bathrooms.

  • fast-dryFast Drying – It allows the painting to be done easily and quickly. It greatly optimizes production times
  • excellent-glossSmooth & Soft feelThe NC Wood Lacquer Color film on the wood offers a high solids film build. It has been specially formulated to provide the best properties for hand rubbing and polishing
  • more-colorsColors on your choice – You can produce an unlimited range of solid color interior wood lacquers using any machine colorants

Product Information

Packsize Available
1L paint
4L paint
20L paint
Choose Your Favourite Finish

glossy-wood

matt-wood

Coverage

Coverage

80-100 Sqft/L/Coat

**coverage may vary based on the type of wood used and the application methodology

 

Choose Your Favourite Finish

glossy-wood

glossy-wood

glossy-wood

Coverage

Coverage

9-10 m²/ℓ per coat at 20 µm DFT

**Coverage may vary based on the type of wood used and the application methodology

Technical Data

drying-timeDrying Time
@30 c and 60% RH

Surface Dry

Surface-dry7 minutes

Tack Free

tack-free1 Hour

Overcoat Interval

overcoat-interval4 Hours

Dry to Handle

gloss808 Hours

Gloss level @ 60

gloss80Gloss

VOC

drying-time650 gm/ litre

Flash Point

drying-timeabove 4 °C

Application Environment Surface Temp Ambient Temp Relative Humidity
Min 15 °C 20 °C 20%
Max 35 °C 40 °C 85%
Application Method-LPS/1K Pri. surfacer Thinner No.of coats Re-coating Time Sanding*
Conventional Spray 100% of NC Thinner D-13X / D-18 2 – 3 4 Hours 320 – 400

*Sand lightly between coats with 320 emery paper to denim. Dust off with dry cloth. This removes upstanding wood fiber ends and dust particles which could draw moisture in behind the film and shorten the life of the coating.

Application Method-Topcoat Color Thinner No.of coats Re-coating Time Sanding
Conventional, Airless, Air Assisted Airless, HVLP 100-125% of NC Thinner SP 58 2 4 Hours 400 / 600
RECOMMENDED USE
ON BARE WOOD

First, allow the bare wood to dry. Make it free of dirt, grease, and other contaminants. Smoothen the surface of the bare wood with recommended sandpaper and then clean the sanding dust from the surface of the wood. Allow the bare wood to dry once again. Fill the wood grains with Sheenlac NC Putty if you do not want the grains to appear.

ON STEEL or IRON

Allow the iron or steel surface to dry first. Make the surface free of dirt, grease, and other contaminants. Sand or wipe with wire-brush to remove mill scales and rust. After that clean the sanded surface and allow it to dry.

ON PRE-PAINTED SURFACE

If the surface is already painted, scrape off any loose and flaking paint film from the surface. Sand and smoothen the defective areas. In the case of ferrous substrates, take care to remove the rust thoroughly. Make the surface free of dirt, grease, and other contaminants. The scraped areas should be spot-primed. Use a primer for metal and an undercoat for wood surfaces to complete the spot priming.

ON WOOD

First, apply one coat of NC Aluminium lacquer as a primer. Follow this by one or two coats of Sheenlac NC Primer surfacer as an undercoat. Finally, give two coats of Sheenlac NC Wood Lacquer – Color.

ON METAL

First, apply one coat of Sheenlac Red oxide / Zinc chrome metal primer. Follow this by one or two coats of Sheenlac NC Primer surfacer as an undercoat. Finally, give two coats of Sheenlac NC Wood Lacquer – Color.

Flag Counter