Select Page

Sheenlac 2000 – 2K Epoxy Red Oxide Primer

SHEENLAC 2000 is a two-pack epoxy red oxide primer with anticorrosive pigments.

AREA OF USAGE

SHEENLAC 2000 is suitable as a topcoat over recommended primers. They are used in general industrial, and a wide range of offshore and onshore applications.SHEENLAC 2000 is recommended only over abrasive blast cleaned surfaces.The best anticorrosion performance of this primer is obtained over metal surfaces.

Shelf Life

24 months for SHEENLAC 2000 Part A and Part B from the date of manufacturing. The mentioned shelf life is applicable only in original tightly closed containers stored away from direct sunlight and excessive heat.

1L paint
4L paint
20L paint

 

download
Download Product Brochure

 

Storage and Transportation

Coverage

Do not store or transport the containers in direct sunlight or at elevated temperatures. Store the container in an upright position to avoid any leakage or damage.

Coverage

Coverage

Theoretical Coverage – 10 ㎡/liter at 50 ㎛ and specified volume solid

Practical Coverage – Allow appropriate loss factors

Technical Data

Color

more-colorsRed oxide

Texture

superior-glossMatte

Solid by Volume

chain50 ± 3%

Dry Film Thickness

overcoat-interval50 -75 ㎛

Method of Application

overcoat-intervalAirless Spray, Air Spray,
Brush

VOC

drying-time< 420 gm/ litre

Drying Times
(·H: Hour, D: Day) 15℃ 25℃ 40℃
Set to Touch 3 Hrs 1½ Hrs 1 Hrs
Dry Hard 10 Hrs 4 Hrs 3 Hrs
Overcoating Interval with recommended topcoats Min 10 Hrs 4 Hrs 3 Hrs
Overcoating Interval with recommended topcoats Max Extended* Extended* Extended*

*Ensure sanding with 220 emery before over-coating

Applications

Overcoat Preparation

  • Stir and mix the paint and hardener properly before use
  • Follow accurate mixing ratios
  • Use recommended thinners only
  • Do not over thin the paint more than the recommended levels

Surface Preparation

  • Ensure removal of all dirt, grease, and loosely bonded or flaking materials from the primed surface
  • Remove all traces of oil or grease with solvent wiping
  • Blast clean the surfaces complying with minimum Sa2½ (ISO 8501-1:2007) or SSPC-SP6
  • Make sure that the recommended surface profile is in the range of 35-50 microns
  • Prepare metal surfaces to the level of Sa2.5
  • Use power tool cleaning complying with SSPC –SP11in situations where it is not possible to do the blasting

Overcoat Preparation Details

Mix Ratio 4 part(s):1 part by volume
Airless Spray Tip Range 0.013″~0.018″
Air Spray (Conventional) Use suitable proprietary equipment
Brush Typically 35-45 microns can be achieved
Thinner Sheenlac 20T Thinner
Dilution Ratio (by volume)
Brush 10% Max
Airless spray As appropriate and lesser than 10 %
Air assisted spray 10-20% Max
(.H:Hour) 15℃ 25℃ 40℃
Pot Life 6H 5H 3H

Application Procedure

  • Apply over the blast cleaned surface or metal surface by following the guidelines as laid out

Application Precautions

  • Do not apply this product over damp substrates or steel below the due point
  • Do not apply when the humidity is above 85%RH
  • Do not use mixed paint after the pot-life period
  • Prepare the surface of the primer before over-coating when exceeding overcoating interval or when exposed to sunlight for a long time
Safety Features
  • Refer the MSDS of the product which is available on request
  • Keep out of reach of children
  • Use personal protective equipment like goggles, face masks, gloves
  • Immediately rinse or wash appropriately using plenty of water in case of contact with eyes or skin
  • Seek medical advice if any sort of irritation persists
  • Do not inhale the vapour or spray
  • Seek immediate medical attention in case of ingestion
  • Use SHEENLAC 2000 only in industrial environments by qualified applicators
Ancillary Products

opulence-exteriorEXTERIOR PENETRATIVE
WOOD STAIN

opulence-exteriorOPULENCE EXTERIOR SEALER

opulence-exteriorPU THINNER D-67

Flag Counter