Sheenlac 2005 – 2K Epoxy Zinc Phosphate Primer

Sheenlac 2005-2K Epoxy Zinc Phosphate primer is a two-component primer.


Sheenlac 2005-2K Epoxy Zinc Phosphate primer is ideal as a medium performance primer. The product is used in general, industrial, OEM and a wide variety of onshore applications.

Shelf Life

12 months for Sheenlac 2005 Part A and Part B from the date of manufacture.
The mentioned shelf life is applicable only when it is stored away from direct sunlight and excessive heat, in original tightly closed containers.

1L paint
4L paint
20L paint

Storage and Transportation


Do not store or transport the containers under direct sunlight or at elevated temperatures.
Store the containers in upright position to avoid leakage or damage.



Theoretical Coverage: 9 ㎡/liter at 50 ㎛ and specified volume solid

Practical Coverage: Allow appropriate loss factors

Technical Data


more-colorsLight Grey, Red oxide, and Yellow / Buff



Solid by Volume

chain45 ± 3%

Dry Film Thickness

overcoat-interval50 -75 ㎛

Method of Application

overcoat-intervalAirless Spray, Air Spray,


drying-time< 500 gm/ litre

Drying Times
(·H: Hour, D: Day) 15℃ 25℃ 40℃
Set to Touch 4 Hrs 2 Hrs 1 Hrs
Dry Hard 12 Hrs 7 Hrs 4 Hrs
Overcoating Interval with recommended topcoats Min 15 Hrs 6 Hrs 4 Hrs
Overcoating Interval with recommended topcoats Max Extended* Extended* Extended*

*Ensure sanding with 220 emery before over-coating


Overcoat Preparation

  • Stir and mix the paint and hardener thoroughly before use.
  • Follow accurate mixing ratios.
  • Use recommended thinners only.
  • Do not over thin the paint more than the recommended levels.

Surface Preparation

  • Ensure removal of dirt, grease, loosely bound or flaking materials from the surface.
  • Remove all traces of oil or grease using solvent wipes.
  • Blast clean the surfaces complying with minimum Sa2.5 (ISO 8501-1:2007) or SSPC-SP6.
  • Ensure that the recommended surface profile is in the range of 35-50 microns.
  • Prepare metal surfaces to the level of Sa2.5.
  • Use power tool cleaning complying with SSPC-SP11 in conditions, where blasting is not possible.

Overcoat Preparation Details

Mix Ratio 4 part(s):1 part by volume
Airless Spray Tip Range 0.013″~0.018″
Air Spray (Conventional) Use suitable proprietary equipment
Brush Typically 35-45 microns can be achieved
Thinner Sheenlac 20T Thinner
Dilution Ratio (by volume)
Brush 10% Max
Airless spray As appropriate and lesser than 10 %
Air-assisted spray 10-20% Max
(.H:Hour) 15℃ 25℃ 40℃
Pot Life 6H 4H 3H

Application Method

  • Apply over the blast cleaned surface or metal surface as per the guidelines provided.

Application Precautions

  • Do not apply this product over damp substrates or steel below the dew point.
  • Do not apply when the humidity is above 85% RH.
  • Do not use mixed paint after the pot-life period.
  • If the over coating interval or sunlight exposure is longer, ensure proper preparation of the surface, before over coating.
Safety Features
  • Refer MSDS of the product, available on request.
  • Keep out of reach of children.
  • Use personal protective equipment like goggles, face masks and gloves.
  • In case of contact with eyes or skin, wash immediately using plenty of water. Seek medical advice, if irritation persists.
  • In case of ingestion, seek immediate medical attention.
  • Do not inhale the vapour or spray.
  • Sheenlac 2005 is intended to be used only in industrial environments by qualified applicators.

Flag Counter